How To Install Cast Iron Kitchen Sink

How to Install a Bandage Iron Tub: Apse, Drop-in, Pedestal, & Clawfoot Footstep-by-Stride

written past: Michael Lamew

Table of Contents

• How to Install a Cast Iron Tub: Alcove, Drop-in, Pedestal, & Clawfoot Step-by-Footstep
  • What You'll Need
  • How to Install a Cast Iron Alcove Tub
  • How to Install a Cast Iron Driblet-in Tub
  • How to Install a Cast Iron Pedestal or Clawfoot Tub
  • Summing It Up: What To Do At present

Welcome to Showersly!

If you're wondering, "How to Install a Cast Atomic number 26 Tub?" you lot're non lone.

Many homeowners fall in love with summit-rated luxury baths like bandage atomic number 26 tubs for their bath remodels, but due to their added weight, more questions naturally arise.

I'm here to answer those questions, and also, as an added bonus, requite my pro tips along the way.

If you need aid selecting a cast iron tub, check my guide to the 11 best cast fe tubs of 2022. You won't want to miss it.

I hope that this page lifts the curtain of mystery on, "How to Install a Cast Atomic number 26 Bathtub," and that you lot enjoy yourself while you're learning. At present let's get started.

---

What You'll Need

Required Materials Required Tools

• Towel
• Silicon sealant
• Metallic shims
• Plumbers putty
• Wallcoverings, if needed
• Wooden boards
• Plumb line

• Safe shoes
• Safe glasses
• Arc pliers or xiv" pipe wrench
  
• Screwdriver
• Tape measure
• Level
  
• Square
  
• Pliers

---

How to Install a Cast Iron Alcove Tub

#1Remove Former Bath

• Disconnect drain with pliers
• Remove old wall textile that may get in the way
• Slip wooden boards underneath one-time tub's feet, to protect flooring
• Slide out one-time tub

#3Gear up Subfloor

Make sure your subfloor is level. Also, bank check if it needs repairs, and/or reinforcement.

#4Make up one's mind Framing

• Take the meridian, width, and length of your new tub, then mark off where your tub will become on your subfloor
• Mark off expanse where bleed will get, let clearance
• Construct a framing recess for your particular tub, nearly unremarkably using 2x4s, making sure to allow room for sub & finished wall

#5Determine Draining

• Cutting a 6″ x 12″ pigsty for the drain (unless it's an to a higher place-the-floor drain install)

#6Partially Install Bathroom Drain

• Install your bleed on your new tub (per bleed manufacturers' instructions)

#7Protect Bath Unit

• Put a towel down at the lesser of your new tub (prevents surface scratches)

#8Install New Cast Atomic number 26 Alcove Tub

• Advisedly slide new tub into frame
• Insert drain tailpipe into bleed hole
• Level bath, using metallic shims (as needed) underneath support feet
  • Bath must be resting on all 4 support feet
• Check level along meridian, and bleed side of tub
  • If bathroom is still unlevel, yous may have to move your tub in & out of the recess area, until it's shimmed properly

#nineInstall Plumbing

CAUTION: risk of damage to subfloor & bath bottom

• Make certain all drain connections are watertight
• In one case the bath is prepare, and secure, connect the drain to the trap
  • PRO TIP: Having an "access panel" will just future maintenance

#10Complete Wall Finish

• Protect the bath surface
• Install gypsum wallboard, roofing frames and walls
• Apply a dewdrop of silicon sealant where the gypsum wallboard meets the tub
• Install the wall covering (subwall), go down until 1/16″ from tub surface
• Install the finished wall material to the subwall
• Apply your silicon sealant to seal the articulation between the rim of our tub, and the wall
• Install the finished floor
• Apply silicon sealant to bottom edge of your bath apron

#11Install Faucet Handles & Spout

• Install your faucet handles & spot, according to manufacturers instructions

#12Clean Up

Annotation: Avoid abrasive cleaners! (may damage or dull your tub surface)

• Use warm water + liquid detergent to make clean surfaces

---

How to Install a Bandage Iron Drop-in Tub

#1Before You Begin

• Audit new tub for damages / imperfections
• Identify tub on drop material to prevent scratches
• Make certain subfloor is level & can support the full load (weight of the tub & water)
• Ensure you accept proper access to final plumbing locations

#2Site Prep

• WARNING: Do Not support drib-in tubs by their rim, back up past their feet
• Check plumbing supply lines for leaks, then cap
• Construct 2×4 or 2x6 stud framing for tub, permit room for finished wall

#iiiSuggested Framing

• Frame the floor (2×4 or 2×six) stud framing
• Provide 1/xvi″ gap between framing & bathtub rim (for finished wall)
• Position the rough-in plumbing
• Verify subfloor & framing can support tub, also brand certain their level

#ivInstall Drain

• Circumspection #one: Practice NOT lift without assistance, cast iron tubs are some of the heaviest tubs out there, then you'll need aid
• CAUTION #2: Do NOT back up your cast fe drop-in tub by it'due south rim
• Install your drain, according to bleed manufacturer's instructions
• Place drop textile inside tub to protect from scratches

#5Install Bandage Iron Drop-In Tub

• CAUTION #1 & #ii still hold true
• Using help, move your bathtub into postion, within your frame
• Once in position, verify that your tub is level
  • Using your metallic shims, adjust if necessary under feet
• PRO TIP: For future maintenance allow access to plumbing

#6Install Plumbing

• CAUTION: Ensure your connections are watertight, prevents leaks & property impairment
• Connect your drain to your tap, according to drain manufacturer's specifications
• Install your faucet valve, according to faucet manufacturer's specifications
• Open your water supply, check ALL connections for leaks
• Fill up your new cast iron drop-in tub to the overflow, check for leaks

#7Complete Finished Wall

• Install finished wall textile / tile, leave i/xvi″ gap for silicon sealant
• Seal with silicon sealant
• Install faucet trim, co-ordinate to faucet manufacturer's instructions

#8Make clean Up

• CAUTION: AVOID acidic & alkaline metal based cleaners, will damage cast iron enamel
• Employ a neutral detergent, soft material, and warm water to scrub away any dirt / imperfections

---

How to Install a Cast Iron Pedestal or Clawfoot Tub

#oneBefore You Begin

• Make sure your floor tin can support your new tub'southward load
• Verify floor is level
• Once you receive your new tub, with a pencil, mark your dimensions in the flooring where your new tub will go

#2Identify Your New Tub In Your Desired Location

• Once into identify, drop a plumb line from your new tub's overflow drain
  • Determines your drain location
• Marker your drain hole location on your floor

#threeMove Tub To Install Plumbing

• Once your tub is out of the style, install your drain & waste pipping at the appropriate superlative
  • To determine this, pre-install your drain pipping to your tub, and measure length to the floor (where your drain will be)

#4Fix Tub Back Into Position – Level

• Carefully, set your tub back into position, level with metal shims if necessary
  • For cast iron pedestal tubs: apply a bead of silicon to leveling feet in one case into place, to prevent hereafter motility

#5Trim Drain & Overflow Pipes

• Once your tub is prepare into place, trim your bleed piping, and overflow pipage to the required length

#half-dozenUse Plumber's Tape To Prep Drain & Overflow Pipes

• One time your drain & overflow pipes are properly trimmed, put plumbers record around the threads at all ends

#7Employ Silicon Sealant To Bleed Flange

• Now that your tub is in place, and your pipes are prepped, apply your silicon sealant to the bleed flange underneath your tub
• Next, get your drain flange, and thread it through your tub, to your drain pipe
  • Utilise silicon sealant, or plumbers tape, to ensure a watertight seal
  • Circumspection: Failure to provide a watertight seal, with your drain, tin atomic number 82 to significant h2o damage, so be conscientious
• Tighten your drain flange by hand, wiping abroad whatever backlog silicon sealant

#8Install Overflow Piping

• Install your overflow assembly (overflow plate, beveled washer, and mounting screw)
  • Use your silicon sealant underneath the flange, to ensure a watertight seal

#9Connect Waste product Drain to Overflow Pipping

• Using sealing washers, and skid nuts, connect the waste material & overflow tee
  • Beveled end of the washer should face the tee

#10Connect Waste & Overflow Tee to Floor Bleed

• Askew end of the washer should face the tee

#11Now That Your Tub Is Set, Check for Leaks

• Once tub is in place, and all connections are made, check for leaks
  • This can be done by slowly filling up your tub with water, making sure the overflow drain, and waste matter drain are watertight

#12For Cast Iron Pedestal Tubs ONLY

• Employ silicon sealant around the base of operations of your pedestal tub, wipe away excess sealant

#13Clean Upwards

• Same goes as the other tubs, Avoid acidic & element of group i-based, will damage your tub
  • Instead, use warm water, a neutral detergent, and a soft material

---

Summing It Up: What To Do Now

There you have information technology.

After reading this folio, y'all should have a good idea on how to perform your cast iron bath installation.

Once again, as we've said many times throughout this guide, bandage iron tubs are HEAVY, and so you MUST check if your floor/subfloor tin can support this significant amount of added weight.

In one case yous get the green light that your flooring can support the weight, you're all set to savor your cast iron bath and it's benefits.

Now, if yous're looking for highly-reviewed models for 2022, check out our cast-atomic number 26 bathtub reviews with our top 11 units for the twelvemonth.

---

Desire more money-saving articles to help yous build your dream bathroom super-easy?

Like how do walk-in tubs work, or mayhap, you lot're looking for the best freestanding tub 2022 has available.

Click our logo epitome below to proceed your journey.

Disclaimer: If you're unfamiliar with installing bathroom fixtures, and plumbing, consult with a professional person Earlier attempting to install. Showersly will Not accept liability for whatever harm to tubs, floors, walls, and/or personal injury, due to improper installation. To preclude improper installation, follow the exact instructions provided by each of your equipment'due south manufacturers. Use this page as a mere guideline, not exact instructions. Use trained professionals for proper installation.

Source: https://www.showersly.com/how-to-install-cast-iron-tub/

Posted by: wheelerbenctes78.blogspot.com

Share this post